"Constrained Material" not selectable in Part Entry - Epicor 905

system · February 10, 2015, 5:43pm

It looks like we DO have Advanced Material Management enabled in our 9.05 (itâ€™s under Data Collection), but we DO NOT have it in our 8.03. We donâ€™t have Advanced Scheduling in either system. Any ideas????

Mike Abell

Information Technology Manager
Flexial - BOA Group - Cookeville, Tennessee
Office: 931.432.8408
Mobile: 615.418.3055
email: MAbell@...

From: vantage@yahoogroups.com [mailto:vantage@yahoogroups.com]
Sent: Tuesday, February 10, 2015 4:19 PM
To: 'vantage@yahoogroups.com'
Subject: RE: [Vantage] Re: "Constrained Material" not selectable in Part Entry - Epicor 905-702.

correct

Rob Bucek
Production Control Manager
PH: (715) 284-5376 ext 311
Mobile: (715)896-3119
FAX: (715)284-4084
[cid:1.234354861@...]<http://www.dsmfg.com/>
(Click the logo to view our site)<http://www.dsmfg.com/>

From: vantage@yahoogroups.com [mailto:vantage@yahoogroups.com]
Sent: Tuesday, February 10, 2015 4:19 PM
To: vantage@yahoogroups.com
Subject: [Vantage] Re: "Constrained Material" not selectable in Part Entry - Epicor 905-702.

Have you checked the modules in the license applied to E9Test?
I thought "Constrained" was dependant on either the AdvSched or AMM module.

[Non-text portions of this message have been removed]

system · February 10, 2015, 5:03pm

We recently upgraded our 8.03 database to test Epicor 905-702. Most, if not all, of our purchase parts have the “contrained material” checkbox checked on them in our Vantage 8.03 database. However, when we pull the same parts in on the upgrade 9.05 database, it is unchecked and we cannot check the box at all. In fact, we can’t even check it if we create a NEW part from scratch. Is this a bug in our setup????

Mike Abell

Information Technology Manager
Flexial - BOA Group - Cookeville, Tennessee
Office: 931.432.8408
Mobile: 615.418.3055
email: MAbell@...

system · February 10, 2015, 5:18pm

Have you checked the modules in the license applied to E9Test?
I thought "Constrained" was dependant on either the AdvSched or AMM module.

system · February 10, 2015, 5:19pm

correct

Rob Bucek
Production Control Manager
PH: (715) 284-5376 ext 311
Mobile: (715)896-3119
FAX: (715)284-4084
[cid:1.234354861@...]<http://www.dsmfg.com/>
(Click the logo to view our site)<http://www.dsmfg.com/>

From: vantage@yahoogroups.com [mailto:vantage@yahoogroups.com]
Sent: Tuesday, February 10, 2015 4:19 PM
To: vantage@yahoogroups.com
Subject: [Vantage] Re: "Constrained Material" not selectable in Part Entry - Epicor 905-702.

Have you checked the modules in the license applied to E9Test?
I thought "Constrained" was dependant on either the AdvSched or AMM module.

[Non-text portions of this message have been removed]

system · February 10, 2015, 5:39pm

Rob, we had neither of those in our Vantage 8.03 but we were able to select it and use it.

Mike Abell

Information Technology Manager
Flexial - BOA Group - Cookeville, Tennessee
Office: 931.432.8408
Mobile: 615.418.3055
email: MAbell@...

From: vantage@yahoogroups.com [mailto:vantage@yahoogroups.com]
Sent: Tuesday, February 10, 2015 4:19 PM
To: 'vantage@yahoogroups.com'
Subject: RE: [Vantage] Re: "Constrained Material" not selectable in Part Entry - Epicor 905-702.

correct

Rob Bucek
Production Control Manager
PH: (715) 284-5376 ext 311
Mobile: (715)896-3119
FAX: (715)284-4084
[cid:1.234354861@...]<http://www.dsmfg.com/>
(Click the logo to view our site)<http://www.dsmfg.com/>

From: vantage@yahoogroups.com [mailto:vantage@yahoogroups.com]
Sent: Tuesday, February 10, 2015 4:19 PM
To: vantage@yahoogroups.com
Subject: [Vantage] Re: "Constrained Material" not selectable in Part Entry - Epicor 905-702.

Have you checked the modules in the license applied to E9Test?
I thought "Constrained" was dependant on either the AdvSched or AMM module.

[Non-text portions of this message have been removed]