PartWhse.OnHandQty

PartBin does not give me the total in my warehouse.



_____

From: Mike Lowe [mailto:MLowe@...]
Sent: Tuesday, September 06, 2005 11:50 AM
To: vantage@yahoogroups.com
Subject: RE: [Vantage] PartWhse.OnHandQty



Try PartBin instead of PartWhse.

Mike

-----Original Message-----
From: vantage@yahoogroups.com [mailto:vantage@yahoogroups.com]On Behalf
Of RICH WAGNER
Sent: Tuesday, September 06, 2005 8:45 AM
To: vantage@yahoogroups.com
Subject: [Vantage] PartWhse.OnHandQty


I have a BAM setup that alerts us when the PartWhse.OnHandQty goes below
the PartPlant.MinimumQty. The email alert always indicates the correct
MinimumQty but the OnHandQty is not always correct.



Sometimes on a STK-STK Transaction the alert gives me the transacted
quantity where I should get the OnHandQty. Other times I get the
amount in one bin even though the Part is in multiple bins.



I am unsure how to troubleshoot this. Can anyone tell me how the
OnHandQty is calculated and could Vantage possible be putting a
temporary value in the OnHandQty until it is properly calculated?



[Non-text portions of this message have been removed]



Useful links for the Yahoo!Groups Vantage Board are: ( Note: You must
have already linked your email address to a yahoo id to enable access. )
(1) To access the Files Section of our Yahoo!Group for Report Builder
and Crystal Reports and other 'goodies', please goto:
http://groups.yahoo.com/group/vantage/files/.
<http://groups.yahoo.com/group/vantage/files/>
(2) To search through old msg's goto:
http://groups.yahoo.com/group/vantage/messages
(3) To view links to Vendors that provide Vantage services goto:
http://groups.yahoo.com/group/vantage/links



_____

YAHOO! GROUPS LINKS



* Visit your group " vantage
<http://groups.yahoo.com/group/vantage> " on the web.


* To unsubscribe from this group, send an email to:
vantage-unsubscribe@yahoogroups.com
<mailto:vantage-unsubscribe@yahoogroups.com?subject=Unsubscribe>


* Your use of Yahoo! Groups is subject to the Yahoo! Terms of
Service <http://docs.yahoo.com/info/terms/> .


_____




[Non-text portions of this message have been removed]



Useful links for the Yahoo!Groups Vantage Board are: ( Note: You must
have already linked your email address to a yahoo id to enable access. )
(1) To access the Files Section of our Yahoo!Group for Report Builder
and Crystal Reports and other 'goodies', please goto:
http://groups.yahoo.com/group/vantage/files/.
<http://groups.yahoo.com/group/vantage/files/>
(2) To search through old msg's goto:
http://groups.yahoo.com/group/vantage/messages
(3) To view links to Vendors that provide Vantage services goto:
http://groups.yahoo.com/group/vantage/links




_____

YAHOO! GROUPS LINKS



* Visit your group "vantage
<http://groups.yahoo.com/group/vantage> " on the web.

* To unsubscribe from this group, send an email to:
vantage-unsubscribe@yahoogroups.com
<mailto:vantage-unsubscribe@yahoogroups.com?subject=Unsubscribe>

* Your use of Yahoo! Groups is subject to the Yahoo! Terms of
Service <http://docs.yahoo.com/info/terms/> .



_____



[Non-text portions of this message have been removed]
I have a BAM setup that alerts us when the PartWhse.OnHandQty goes below
the PartPlant.MinimumQty. The email alert always indicates the correct
MinimumQty but the OnHandQty is not always correct.



Sometimes on a STK-STK Transaction the alert gives me the transacted
quantity where I should get the OnHandQty. Other times I get the
amount in one bin even though the Part is in multiple bins.



I am unsure how to troubleshoot this. Can anyone tell me how the
OnHandQty is calculated and could Vantage possible be putting a
temporary value in the OnHandQty until it is properly calculated?



[Non-text portions of this message have been removed]
Try PartBin instead of PartWhse.

Mike

-----Original Message-----
From: vantage@yahoogroups.com [mailto:vantage@yahoogroups.com]On Behalf Of RICH WAGNER
Sent: Tuesday, September 06, 2005 8:45 AM
To: vantage@yahoogroups.com
Subject: [Vantage] PartWhse.OnHandQty


I have a BAM setup that alerts us when the PartWhse.OnHandQty goes below
the PartPlant.MinimumQty. The email alert always indicates the correct
MinimumQty but the OnHandQty is not always correct.



Sometimes on a STK-STK Transaction the alert gives me the transacted
quantity where I should get the OnHandQty. Other times I get the
amount in one bin even though the Part is in multiple bins.



I am unsure how to troubleshoot this. Can anyone tell me how the
OnHandQty is calculated and could Vantage possible be putting a
temporary value in the OnHandQty until it is properly calculated?



[Non-text portions of this message have been removed]



Useful links for the Yahoo!Groups Vantage Board are: ( Note: You must have already linked your email address to a yahoo id to enable access. )
(1) To access the Files Section of our Yahoo!Group for Report Builder and Crystal Reports and other 'goodies', please goto: http://groups.yahoo.com/group/vantage/files/.
(2) To search through old msg's goto: http://groups.yahoo.com/group/vantage/messages
(3) To view links to Vendors that provide Vantage services goto: http://groups.yahoo.com/group/vantage/links



_____

YAHOO! GROUPS LINKS



* Visit your group " vantage <http://groups.yahoo.com/group/vantage> " on the web.


* To unsubscribe from this group, send an email to:
vantage-unsubscribe@yahoogroups.com <mailto:vantage-unsubscribe@yahoogroups.com?subject=Unsubscribe>


* Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service <http://docs.yahoo.com/info/terms/> .


_____




[Non-text portions of this message have been removed]