Plant Floor - Touch screen terminals

Yahoo Archive
1
Elo Touch System lists at least 9 different touch technologies. Which
technologies are you using?

Rob McFarlin
Accel Group Inc


--- In vantage@yahoogroups.com, "Roger@..." <rjr-office@...> wrote:
>
> Linda,
>
> we use them(elotouch) also, in a very oily area and they seem to
hold up to greasy fingers as well.
>
> Roger Rabus
> Logical Solutions
>
>
>
> ________________________________
>
> From: vantage@yahoogroups.com on behalf of Aaron Hoyt
> Sent: Thu 1/18/2007 1:29 PM
> To: vantage@yahoogroups.com
> Subject: RE: [Vantage] Plant Floor - Touch screen terminals
>
>
>
> Linda,
> Yes,
> Using 7 EloTouch monitors for Plant Floor. I highly recommend the
> IntelliTouch type that we use.
> The user touches directly on the glass of the monitor. No overlay,
no wear.
> They can be used with a gloved hand. They can't be used with hard
objects
> like screwdrivers or hammers (though we have a chip in one monitor
that no
> one is willing to explain, but it still works just fine).
> They require an initial calibration, but I have never had to
recalibrate any
> of them (over two years in service).
> Users initially told me how they had tried shop floor before and
how it
> didn't work and how much time it took and how it was not going to
work this
> time...Once rolled out with some initial training, within one week
there was
> not a single complaint left on the shop floor.
> Think of Shop Floor as the Ice-Cream, barcodes and scanners as the
> sprinkles, but touch monitors are the cone that makes it all user
friendly.
> :)
> Good luck,
> Aaron Hoyt
> Vantage Plastics
> -----Original Message-----
> From: vantage@yahoogroups.com <mailto:vantage%40yahoogroups.com>
[mailto:vantage@yahoogroups.com <mailto:vantage%40yahoogroups.com> ]
On Behalf Of
> cricketllb
> Sent: Wednesday, January 17, 2007 8:32 AM
> To: vantage@yahoogroups.com <mailto:vantage%40yahoogroups.com>
> Subject: [Vantage] Plant Floor - Touch screen terminals
>
> Is anyone using a touch screen terminal for the Plant Floor
> application? We are running Vantage 6.1.533. What terminal do you
> use? Does it run well? Any problems?
>
> Thanks,
>
> - Linda Beaudreau
>
> [Non-text portions of this message have been removed]
>
>
>
>
>
>
> [Non-text portions of this message have been removed]
>
2
Is anyone using a touch screen terminal for the Plant Floor
application? We are running Vantage 6.1.533. What terminal do you
use? Does it run well? Any problems?

Thanks,

- Linda Beaudreau
3
Linda,
Yes,
Using 7 EloTouch monitors for Plant Floor. I highly recommend the
IntelliTouch type that we use.
The user touches directly on the glass of the monitor. No overlay, no wear.
They can be used with a gloved hand. They can't be used with hard objects
like screwdrivers or hammers (though we have a chip in one monitor that no
one is willing to explain, but it still works just fine).
They require an initial calibration, but I have never had to recalibrate any
of them (over two years in service).
Users initially told me how they had tried shop floor before and how it
didn't work and how much time it took and how it was not going to work this
time...Once rolled out with some initial training, within one week there was
not a single complaint left on the shop floor.
Think of Shop Floor as the Ice-Cream, barcodes and scanners as the
sprinkles, but touch monitors are the cone that makes it all user friendly.
:)
Good luck,
Aaron Hoyt
Vantage Plastics
-----Original Message-----
From: vantage@yahoogroups.com [mailto:vantage@yahoogroups.com]On Behalf Of
cricketllb
Sent: Wednesday, January 17, 2007 8:32 AM
To: vantage@yahoogroups.com
Subject: [Vantage] Plant Floor - Touch screen terminals


Is anyone using a touch screen terminal for the Plant Floor
application? We are running Vantage 6.1.533. What terminal do you
use? Does it run well? Any problems?

Thanks,

- Linda Beaudreau






[Non-text portions of this message have been removed]
4
Linda,

we use them(elotouch) also, in a very oily area and they seem to hold up to greasy fingers as well.

Roger Rabus
Logical Solutions



________________________________

From: vantage@yahoogroups.com on behalf of Aaron Hoyt
Sent: Thu 1/18/2007 1:29 PM
To: vantage@yahoogroups.com
Subject: RE: [Vantage] Plant Floor - Touch screen terminals



Linda,
Yes,
Using 7 EloTouch monitors for Plant Floor. I highly recommend the
IntelliTouch type that we use.
The user touches directly on the glass of the monitor. No overlay, no wear.
They can be used with a gloved hand. They can't be used with hard objects
like screwdrivers or hammers (though we have a chip in one monitor that no
one is willing to explain, but it still works just fine).
They require an initial calibration, but I have never had to recalibrate any
of them (over two years in service).
Users initially told me how they had tried shop floor before and how it
didn't work and how much time it took and how it was not going to work this
time...Once rolled out with some initial training, within one week there was
not a single complaint left on the shop floor.
Think of Shop Floor as the Ice-Cream, barcodes and scanners as the
sprinkles, but touch monitors are the cone that makes it all user friendly.
:)
Good luck,
Aaron Hoyt
Vantage Plastics
-----Original Message-----
From: vantage@yahoogroups.com <mailto:vantage%40yahoogroups.com> [mailto:vantage@yahoogroups.com <mailto:vantage%40yahoogroups.com> ]On Behalf Of
cricketllb
Sent: Wednesday, January 17, 2007 8:32 AM
To: vantage@yahoogroups.com <mailto:vantage%40yahoogroups.com>
Subject: [Vantage] Plant Floor - Touch screen terminals

Is anyone using a touch screen terminal for the Plant Floor
application? We are running Vantage 6.1.533. What terminal do you
use? Does it run well? Any problems?

Thanks,

- Linda Beaudreau

[Non-text portions of this message have been removed]






[Non-text portions of this message have been removed]