# Progress Error
**Category:** [Yahoo Archive](https://www.epiusers.help/c/yahoo-archive/9)
**Created:** 2001-02-08 12:42 UTC
**Views:** 511
**Replies:** 3
**URL:** https://www.epiusers.help/t/progress-error/2190
---
## Post #1 by @system
I am trying to create an export using Results. Then generating the code. I
was doing fine until I added a table that had to be setup as an outer join.
Now I am getting the following errors. I can send my code if anyone is
willing to help me. Cuz I am lost.
** More than 4096 characters in a single statement--use -inp parm. (135)
** Could not understand line 133. (193)
** Unable to understand after -- "G". (247)
** Could not understand line 198. (198)
** More than 4096 characters in a single statement--use -inp parm. (135)
** Could not understand line 206. (193)
** Unable to understand after -- "mt = ?". (247)
** Could not understand line 271. (198)
---
## Post #2 by @system
I would like to take a look at it for you. Can you e-mail your code
to "
kulbacki@..." instead of the sender's e-mail
address?
Ed
--- In vantage@y..., "Reilly, Rhonda" <rreilly@O...> wrote:
> I am trying to create an export using Results. Then generating the
code. I
> was doing fine until I added a table that had to be setup as an
outer join.
> Now I am getting the following errors. I can send my code if
anyone is
> willing to help me. Cuz I am lost.
>
>
>
>
> ** More than 4096 characters in a single statement--use -inp parm.
(135)
> ** Could not understand line 133. (193)
> ** Unable to understand after -- "G". (247)
> ** Could not understand line 198. (198)
> ** More than 4096 characters in a single statement--use -inp parm.
(135)
> ** Could not understand line 206. (193)
> ** Unable to understand after -- "mt = ?". (247)
> ** Could not understand line 271. (198)
If you haven't fixed the problem already send me a copy of your code and
I'll take a look at it.
Mark Kohring
Delta Centrifugal Corp
MKohring@...
-----Original Message-----
From: Reilly, Rhonda [mailto:
rreilly@...]
Sent: Thursday, February 08, 2001 11:34 AM
To:
vantage@yahoogroups.com
Subject: [Vantage] Progress Error
I am trying to create an export using Results. Then generating the code. I
was doing fine until I added a table that had to be setup as an outer join.
Now I am getting the following errors. I can send my code if anyone is
willing to help me. Cuz I am lost.
** More than 4096 characters in a single statement--use -inp parm. (135)
** Could not understand line 133. (193)
** Unable to understand after -- "G". (247)
** Could not understand line 198. (198)
** More than 4096 characters in a single statement--use -inp parm. (135)
** Could not understand line 206. (193)
** Unable to understand after -- "mt = ?". (247)
** Could not understand line 271. (198)
To unsubscribe from this group, send an email to:
vantage-unsubscribe@egroups.comIn your vantage.vtg file under other parameters add the following -inp 10000
. This should take care of the error.
Mark Charamut
President
Caesar Development Services, LLC
Epicor Authorized Independent Solution Provider
mcharamut@...
www.caesardev.com
(860) 667-3540
-----Original Message-----
From: Reilly, Rhonda [mailto:
rreilly@...]
Sent: Thursday, February 08, 2001 12:34 PM
To:
vantage@yahoogroups.com
Subject: [Vantage] Progress Error
I am trying to create an export using Results. Then generating the code. I
was doing fine until I added a table that had to be setup as an outer join.
Now I am getting the following errors. I can send my code if anyone is
willing to help me. Cuz I am lost.
** More than 4096 characters in a single statement--use -inp parm. (135)
** Could not understand line 133. (193)
** Unable to understand after -- "G". (247)
** Could not understand line 198. (198)
** More than 4096 characters in a single statement--use -inp parm. (135)
** Could not understand line 206. (193)
** Unable to understand after -- "mt = ?". (247)
** Could not understand line 271. (198)
To unsubscribe from this group, send an email to:
vantage-unsubscribe@egroups.com