Remember that the patch is specific to the version of Progress you install. You can't apply a 9.1 patch to a 9.0 install, and vice versa.

Randy Vander Galien wrote:

> I am currently preparing to take my first look at 4.00 and I have noticed
> that there are two Progress patches available for download, 9.1a26 and
> 9.0b44. For those users currently on 4.00 is there a preferred patch level
> or is the most current patch (9.1a26) stable? I would like to bring the
> install up to the current patch levels immediately after installation and I
> am looking for some advice.
>
> Randy Vander Galien
> IS Manager
> Wisconsin EPS
>
>
> We no longer allow attachments to files. To access/share Report Files, please go to the following link: http://www.egroups.com/files/vantage/
> (Note: If this link does not work for you the first time you try it, go to www.egroups.com, login and be sure to save your password, choose My Groups, choose Vantage, then choose Files. If you save the password, the link above will work the next time you try it.)

--
/* ============================================================== */

William E. Colls Tel 613 591 0079
PROComputer Systems Fax 613 591 3924
67 Willow Glen Dr www.procomsys.com
Kanata Ontario Canada PEG Member 1998051404

Specialists in Progress Software development since 1985

I am currently preparing to take my first look at 4.00 and I have noticed
that there are two Progress patches available for download, 9.1a26 and
9.0b44. For those users currently on 4.00 is there a preferred patch level
or is the most current patch (9.1a26) stable? I would like to bring the
install up to the current patch levels immediately after installation and I
am looking for some advice.

Randy Vander Galien
IS Manager
Wisconsin EPS

--- In vantage@egroups.com, Randy Vander Galien <randyv@w...> wrote:

> I am currently preparing to take my first look at 4.00 and I have

noticed

> that there are two Progress patches available for download, 9.1a26

and

> 9.0b44. For those users currently on 4.00 is there a preferred

patch level

> or is the most current patch (9.1a26) stable? I would like to bring

the

> install up to the current patch levels immediately after

installation and I

> am looking for some advice.
>
> Randy Vander Galien
> IS Manager
> Wisconsin EPS

You must have Progress 9.1 installed to install the 9.1a26 patch. I
found out the hard way.

The 9.1a26 patch is for Vantage 5.0
9.0b44 is for Vantage 4.0.
And no I don't have Vantage 5.0.................

Ron Newell
IT/MIS
Neon Products
1695 Sargent Ave.
Winnipeg, MB R3H 0C4
http://www.neon-products.com/
mailto:rnewell@...

This message is intended only for the use of the person(s) ("intended
recipient")
to whom it is addressed. It may contain information which is privileged and
confidential.
If you are not the intended recipient please contact the sender as soon as
possible.
Accordingly any dissemination, distribution, copying or other use of this
message or any
of its content by any person other than the Intended Recipient is strictly
prohibited. We
have taken every precaution to ensure that this message is virus free but
we can not be
responsible for any damage that may be caused by its content.

-----Original Message-----
From: Joan Glenn [mailto:jglenn@...]
Sent: Monday, December 04, 2000 3:08 PM
To: vantage@egroups.com
Subject: [Vantage] Re: Progress Patch Level

--- In vantage@egroups.com, Randy Vander Galien <randyv@w...> wrote:
> I am currently preparing to take my first look at 4.00 and I have
noticed
> that there are two Progress patches available for download, 9.1a26
and
> 9.0b44. For those users currently on 4.00 is there a preferred
patch level
> or is the most current patch (9.1a26) stable? I would like to bring
the
> install up to the current patch levels immediately after
installation and I
> am looking for some advice.
>
> Randy Vander Galien
> IS Manager
> Wisconsin EPS

You must have Progress 9.1 installed to install the 9.1a26 patch. I
found out the hard way.

We no longer allow attachments to files. To access/share Report Files,
please go to the following link: http://www.egroups.com/files/vantage/
(Note: If this link does not work for you the first time you try it, go to
www.egroups.com, login and be sure to save your password, choose My Groups,
choose Vantage, then choose Files. If you save the password, the link above
will work the next time you try it.)