E10.700.4 Making Part Inactive

Thanks

 

From: vantage@yahoogroups.com [mailto:vantage@yahoogroups.com]
Sent: Friday, July 10, 2015 1:30 PM
To: vantage@yahoogroups.com
Subject: RE: [Vantage] E10.700.4 Making Part Inactive

 




You can’t inactivate a part with an onhand qty.

 

From: vantage@yahoogroups.com [mailto:vantage@yahoogroups.com]
Sent: Friday, July 10, 2015 10:29 AM
To: 'vantage@yahoogroups.com'
Subject: RE: [Vantage] E10.700.4 Making Part Inactive

 

 

Zeros everywhere except one warehouse has qty on hand

 

From: vantage@yahoogroups.com [mailto:vantage@yahoogroups.com]
Sent: Friday, July 10, 2015 1:25 PM
To: vantage@yahoogroups.com
Subject: RE: [Vantage] E10.700.4 Making Part Inactive

 




In Part Tracker  under > On hand > Warehouses – see if there is any demand.

 

 

 

From: vantage@yahoogroups.com [mailto:vantage@yahoogroups.com]
Sent: Friday, July 10, 2015 10:02 AM
To: vantage@yahoogroups.com
Subject: [Vantage] E10.700.4 Making Part Inactive

 

 

Trying to make some part numbers inactive.

Getting message back from DMT "Part can not be marked inactive if there is quantity allocated."

 

I have run the conversion to reset bins, allocations and the message persists.

I have looked at item in part tracker and there is no qty allocated being shown.

 

Any Ideas on where else I can look to find the reason this part will not be allowed to be inactive?

The option is grayed out in Part maint.

 




 




Trying to make some part numbers inactive.

Getting message back from DMT "Part can not be marked inactive if there is quantity allocated."


I have run the conversion to reset bins, allocations and the message persists.

I have looked at item in part tracker and there is no qty allocated being shown.


Any Ideas on where else I can look to find the reason this part will not be allowed to be inactive?

The option is grayed out in Part maint.

In Part Tracker under > On hand > Warehouses – see if there is any demand.

 

 

 

From: vantage@yahoogroups.com [mailto:vantage@yahoogroups.com]
Sent: Friday, July 10, 2015 10:02 AM
To: vantage@yahoogroups.com
Subject: [Vantage] E10.700.4 Making Part Inactive

 

 

Trying to make some part numbers inactive.

Getting message back from DMT "Part can not be marked inactive if there is quantity allocated."

 

I have run the conversion to reset bins, allocations and the message persists.

I have looked at item in part tracker and there is no qty allocated being shown.

 

Any Ideas on where else I can look to find the reason this part will not be allowed to be inactive?

The option is grayed out in Part maint.

Zeros everywhere except one warehouse has qty on hand

 

From: vantage@yahoogroups.com [mailto:vantage@yahoogroups.com]
Sent: Friday, July 10, 2015 1:25 PM
To: vantage@yahoogroups.com
Subject: RE: [Vantage] E10.700.4 Making Part Inactive

 




In Part Tracker  under > On hand > Warehouses – see if there is any demand.

 

 

 

From: vantage@yahoogroups.com [mailto:vantage@yahoogroups.com]
Sent: Friday, July 10, 2015 10:02 AM
To: vantage@yahoogroups.com
Subject: [Vantage] E10.700.4 Making Part Inactive

 

 

Trying to make some part numbers inactive.

Getting message back from DMT "Part can not be marked inactive if there is quantity allocated."

 

I have run the conversion to reset bins, allocations and the message persists.

I have looked at item in part tracker and there is no qty allocated being shown.

 

Any Ideas on where else I can look to find the reason this part will not be allowed to be inactive?

The option is grayed out in Part maint.

 




You can’t inactivate a part with an onhand qty.

 

From: vantage@yahoogroups.com [mailto:vantage@yahoogroups.com]
Sent: Friday, July 10, 2015 10:29 AM
To: 'vantage@yahoogroups.com'
Subject: RE: [Vantage] E10.700.4 Making Part Inactive

 

 

Zeros everywhere except one warehouse has qty on hand

 

From: vantage@yahoogroups.com [mailto:vantage@yahoogroups.com]
Sent: Friday, July 10, 2015 1:25 PM
To: vantage@yahoogroups.com
Subject: RE: [Vantage] E10.700.4 Making Part Inactive

 





In Part Tracker  under > On hand > Warehouses – see if there is any demand.

 

 

 

From: vantage@yahoogroups.com [mailto:vantage@yahoogroups.com]
Sent: Friday, July 10, 2015 10:02 AM
To: vantage@yahoogroups.com
Subject: [Vantage] E10.700.4 Making Part Inactive

 

 

Trying to make some part numbers inactive.

Getting message back from DMT "Part can not be marked inactive if there is quantity allocated."

 

I have run the conversion to reset bins, allocations and the message persists.

I have looked at item in part tracker and there is no qty allocated being shown.

 

Any Ideas on where else I can look to find the reason this part will not be allowed to be inactive?

The option is grayed out in Part maint.